Slick way to mount a clip to a oar - Mountain Buzz
 



Reply
 
Thread Tools Display Modes
 
Old 08-11-2013   #1
 
Fairbanks, Alaska
Join Date: Aug 2013
Posts: 45
Slick way to mount a clip to a oar



I learned on pins and clips and this is good way to mount them with out lumps and sharp edges.
These are called punchloc bands used to put fittings onto hoses.
Work nicely for oars without ever, ever coming loose.

knucklenuts is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-11-2013   #2
 
Andy H.'s Avatar
 
Wheat Ridge, Colorado
Paddling Since: 1995
Join Date: Oct 2003
Posts: 3,774
knucklenuts,

That looks like a really great way to mount your oars and I encourage everyone to either use something like that or wrap your hose clamps with tape or something else to cover all the sharp points and edges on your oars. Without getting into the oarlocks vs pins and clips stuff, P&Cs tend to have lots of sharp places that can be dangerous. I once dressed a P&Cs-inflicted wound on Brown's that required 42 stitches - yowch!

Be safe out there,

-AH
__________________
Nothing in the world is more yielding and gentle than water. Yet it has no equal for conquering the resistant and tough. The flexible can overcome the unbending; the soft can overcome the hard. - Lao Tse
Andy H. is offline   Reply With Quote
Old 08-11-2013   #3
fat guy in a little boat
 
bigben's Avatar
 
FtC / Rancho del Rio, Colorado
Paddling Since: 8AM
Join Date: Oct 2010
Posts: 409
very nice!! that looks slick.
punchloc you say?? i assume that's not too hard to find.. but is that a rivet holding it together?? perhaps one that "punches" through easily?? (as in a good excuse to whack something with a hammer!)

...i manage a company running pins & clips on ancient bucket boats. i go through a lot of duct tape trying to cover the sharp edges on them hose clamps.
good tip there bro. time to see how well stocked the ace hardware in the middle of nowhere is!!

AndyH.. 42 stitches!!!!! wow, now that's dedication!!! especially when there's a road so close-by
__________________

All I need are some tasty waves, a cool buzz, and I'm fine.
- Spicoli
bigben is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-11-2013   #4
 
Fairbanks, Alaska
Join Date: Aug 2013
Posts: 45
Quote:
Originally Posted by Andy H. View Post
knucklenuts,

That looks like a really great way to mount your oars and I encourage everyone to either use something like that or wrap your hose clamps with tape or something else to cover all the sharp points and edges on your oars. Without getting into the oarlocks vs pins and clips stuff, P&Cs tend to have lots of sharp places that can be dangerous. I once dressed a P&Cs-inflicted a wound on Brown's that required 42 stitches - yowch!

Be safe out there,

-AH
AH,
Call me nuts, please, hah!!
I made these clips and made sure to radius all edges for that very reason.
That can be done on the factory ones quite easily too.
The other thing I use to do is put a fair sized boat trailer roller at the top of the pin to soften it if you fall on it.
So the only sharp edges left would be the less than ideal hose clamps, which these clamps cure.
Thanks
knucklenuts is offline   Reply With Quote
Old 08-11-2013   #5
 
Fairbanks, Alaska
Join Date: Aug 2013
Posts: 45
Quote:
Originally Posted by bigben View Post
very nice!! that looks slick.
punchloc you say?? i assume that's not too hard to find.. but is that a rivet holding it together?? perhaps one that "punches" through easily?? (as in a good excuse to whack something with a hammer!)

...i manage a company running pins & clips on ancient bucket boats. i go through a lot of duct tape trying to cover the sharp edges on them hose clamps.
good tip there bro. time to see how well stocked the ace hardware in the middle of nowhere is!!

AndyH.. 42 stitches!!!!! wow, now that's dedication!!! especially when there's a road so close-by
Big Ben,
Not a rivet, but a indent thru the collar and two layers of the banding.
You won't find these at your ace hardware.
For joe blow I would recommend going to a shop that makes up hoses and have them do it.
Being as your in the business, you may want to buy the tool that tensions and locks them.
I was lucky and found the tool at a auction.
New the tool is around $140.00
Bands are around $2.00 apiece
You might google it for more detail.
knucklenuts is offline   Reply With Quote
Old 08-12-2013   #6
 
fdon's Avatar
 
Christopher Creek, Arizona
Paddling Since: 1969
Join Date: Jul 2008
Posts: 311
yet another reason to roll with open locks...more shit in the repair box=a bigger box. seriously though, that tool with clamps are the way to fab and repair compressed air hose but we are talking about raft equipment here?
fdon is offline   Reply With Quote
Old 08-12-2013   #7
 
Fairbanks, Alaska
Join Date: Aug 2013
Posts: 45
Quote:
Originally Posted by fdon View Post
yet another reason to roll with open locks...more shit in the repair box=a bigger box. seriously though, that tool with clamps are the way to fab and repair compressed air hose but we are talking about raft equipment here?
I came to this site to share some of the things that have worked for me thru the years, this method of attaching clips is getting as close to bear proof as I've seen.
So no need for more poop in the repair box.
I like Andy H have no desire to debate pins and clips versus oarlocks nor any other argument.
Yes, we are talking raft equipment here and I cannot see the difference between repurposing these clamps and the standard hose clamps that are usually used that are far from perfect.
Call me nuts
knucklenuts is offline   Reply With Quote
Old 08-13-2013   #8
 
fdon's Avatar
 
Christopher Creek, Arizona
Paddling Since: 1969
Join Date: Jul 2008
Posts: 311
No offense meant there nuts. Sorry if you were offended. I use those clamps and the required tools often enough to know my way around them. I still argue those clamps are difficult to deal with unless you have the tools needed in the repair kit. Just cause you have not had to repair yours in the field does not mean some one else will not. I personally get on water that will spin or break anything out of shape at one point or another and that is the point I was trying to make. Not start some tackle match. Glad it works for you.
fdon is offline   Reply With Quote
Old 08-13-2013   #9
 
MT4Runner's Avatar
 
Kalispell, Montana
Paddling Since: 1997
Join Date: Apr 2012
Posts: 2,796
Who says you must carry the install tool in your repair kit?

Take off the hose clamps.

Take your oars and P&C's to the local hydraulic shop and have them install the punchlocs.

Throw your old hose clamps and a screwdriver in your repair kit.
(You already had spare hose clamps and a screwdriver and some duct tape, right? Right? )

Go boating.



Gear breaks. It doesn't break every trip, but you should expect it and be prepared for it to happen. Those punchlocs might run 3-4 years before needing a repair. I don't see the issue, especially if you're carrying a spare hose clamp or four in your repair kit.

I am not a P&C fan, but to each their own. I'd love to see my friends running P&C's to have these on their oars so I don't get my hands and legs cut up helping them rig or reflip their boats!!
MT4Runner is online now   Reply With Quote
Old 08-13-2013   #10
 
fdon's Avatar
 
Christopher Creek, Arizona
Paddling Since: 1969
Join Date: Jul 2008
Posts: 311
Yea, the install tool is not needed in your kit if you fix with the hose clamps. But it has been my experience that getting those punch clips off is the most difficult part of the job and just a screw driver aint gonna get it done easily. Also, those dudes clamp down tight enough to crush a hollow oar if they are installed by some bozo. I agree they would work well for all the reasons mentioned above. Im just sayin you better consider how they are installed and how you might have to deal with them in the field. Not trying to win or lose here.
fdon is offline   Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Topic Thread Starter Forum Replies Last Post
Oar mount position? Skyman Whitewater Kayaking 3 05-16-2012 10:20 PM
Oar Mount Placement h2ocst Kayaking | Gear Talk 5 05-16-2011 08:01 PM
oar length for rear-mount frame steven Kayaking | Gear Talk 2 09-23-2009 08:21 AM
want to trade NRS 6" frame oar mounts for 8" mount brendodendo Whitewater Kayaking 0 09-07-2004 06:38 PM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -6. The time now is 09:16 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.