Thread Tools Display Modes
Old 06-29-2016   #1
Steamboat Springs, Colorado
Paddling Since: 01
Join Date: Aug 2015
Posts: 1
Table hardware

Looking to put hardware onto a piece of the white plastic sheet (like cutting board material), would be approx 22" x 66 " and it needs stiffening rails so the material wont sag and legs, the space between my frame rails is 19".

Any ideas for custom fabrication, and or a source to purchase just the hardware ?

Dbelohssa is offline   Reply With Quote
Old 06-29-2016   #2
Paul7's Avatar
Post Falls, Idaho
Paddling Since: 2000
Join Date: Aug 2012
Posts: 781
I'd go to Walmart with a tape measure, I've got a folding lifetime table that the hardware unscrew from the top. It's roughly 2'x4' but I think the frame is a couple inches too wide. Also you can order tee nuts and legs from the roll a table company perhaps you could come up with your own reinforcement out of oak or aluminum.

Sent from my SM-G900V using Mountain Buzz mobile app

Paul7 is online now   Reply With Quote
Old 06-29-2016   #3
Dr.AndyDVM's Avatar
Nampa, Idaho
Paddling Since: 2014
Join Date: Jul 2014
Posts: 200
Weld one up with conduit like Cambridge does.

Sent from my iPhone using Mountain Buzz
Dr.AndyDVM is offline   Reply With Quote
Old 06-30-2016   #4
Join Date: Jul 2006
Posts: 55
Send a message via AIM to damax101
Not to hijack this thread, but I had a question about tables and this might give you some ideas.

I have a 16' cat with a very large wood floor. It would be awesome to get some table legs and have a bad as huge kitchen table for big trips. Rigging/loading/unloading issues of the floor aside, I found this and thought it might be perfect. A little expensive, but considering those blue roll up tables go for $100, it might be a good option.

Instant table legs:

Anyone consider this or have better ideas?
damax101 is offline   Reply With Quote
Old 06-30-2016   #5
Commerce/the Junc, Colorado
Join Date: Oct 2015
Posts: 27
I have used these with good results .

Target Precision RB-H1034 Rugged Buddy 34-Inch Folding Sawhorse Legs for One Complete Sawhorse
SigNewt is offline   Reply With Quote
Old 07-01-2016   #6's Avatar
lafayette, Colorado
Paddling Since: 1961
Join Date: May 2010
Posts: 496
This is what I did for legs. If you just reinforce the length of the table with angle iron down the sides should work. Very handy legs when not rafting.

Kool Kitchen Table

Time is like a river. You cannot touch the water twice, because the flow that has passed will never pass again. Enjoy every moment of life on or off the river. is offline   Reply With Quote
Old 07-06-2016   #7
Whoapiglet's Avatar
Denver, Colorado
Paddling Since: 2000
Join Date: Aug 2010
Posts: 296
AAA in Denver sells a metal leg kit. Pre bent legs and all fittings.
Whoapiglet is offline   Reply With Quote
Old 07-06-2016   #8
Steamboat, Colorado
Join Date: Apr 2013
Posts: 20
I have conduit benders you can use if you decide to go that route
efis is offline   Reply With Quote
Old 07-07-2016   #9
Centerville, Utah
Paddling Since: 2010
Join Date: Jul 2015
Posts: 18
I've been thinking about doing the same for my plywood deck. Found this company that has a pretty great selection of just folding legs -
:: Ebco Products Corp - Table Legs & Folding Legs ::
Check out the H-style legs that have adjustable length up to 38" (hate bending over to reach stuff on my roll-a-table haha!)
WWRE Joe is offline   Reply With Quote
Old 07-07-2016   #10
Denver, Colorado
Paddling Since: 2011
Join Date: May 2013
Posts: 90
I have HDPE (Plastic) Decking on my boat and piece on the front bay runs the full width of the raft (across the double rail sides). Under the table I just screwed in 4 threaded plumbing flanges and got ace hardware to cut me 4 pieces of steel pipe and had those threaded on the ends. The four legs just get thrown in the bottom of my drop bag and then get screwed into the table at camp. I made some little shims to put under the flanges so that the legs angle out slightly to increase stability. I did not use any supports under the table.

I love the table bc its one solid piece of cutting board. It is very stable and when its set up I simple wipe it down with some bleach water and get to cooking. The only downside is that plastic is very heavy and the legs are heavy too but the table is simple and strong and I can cut anywhere on the table. I prefer it to the metal tables except for weight.

Treswright3 is offline   Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Topic Thread Starter Forum Replies Last Post
ss bimini hardware Read_N_Run Rafting | Gear Talk 0 06-08-2016 03:11 PM
Roll-A-Table Legs drhughjorgen Whitewater Kayaking 0 04-15-2009 08:42 PM
Making a Table// Hatch Tiggy Kayaking | Gear Talk 10 03-06-2009 09:18 AM
Camp table opinions tyaker Kayaking | Gear Talk 23 07-23-2008 01:15 PM
FREE - PC Hardware Available Andy H. The Eddy 1 11-15-2006 09:34 AM

» Classified Ads

posted by jillyd23

Large NRS DuraSoft Coolers, pick up Salida, CO

small cat frame

posted by Gumbydamnit

Small welded cat frame I used on my 12' legend. It's...

2" Seat Riser Kit for NRS...

posted by penguin

Ever feel like you sit low in your NRS oar frame? I did, so...

Powered by vBadvanced CMPS v3.2.3

Our Communities

Our communities encompass many different hobbies and interests, but each one is built on friendly, intelligent membership.

» More about our Communities

Automotive Communities

Our Automotive communities encompass many different makes and models. From U.S. domestics to European Saloons.

» More about our Automotive Communities

Marine Communities

Our Marine websites focus on Cruising and Sailing Vessels, including forums and the largest cruising Wiki project on the web today.

» More about our Marine Communities

Copyright 2002-2012 Social Knowledge, LLC All Rights Reserved.

All times are GMT -6. The time now is 06:11 PM.

Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2016, vBulletin Solutions, Inc.